View previous topic :: View next topic |
Author |
Message |
smslinkard Tri Five Rookie
Joined: 27 Nov 2010 Posts: 5 Location: Pittsburg, TX
|
Posted: Tue Feb 22, 2011 6:25 pm Post subject: Polishing stainless steel cost |
|
|
Trying to decide if I should pay someone to polish my existing stainless or buy new stuff. Can someone give me an idea what I should expect to pay someone to polish stainless? Do they charge by the foot or by some other factor? Thanks in advance for your help. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
acardon Bel Air
Joined: 12 Jul 2005 Posts: 273 Location: Southlake, Tx.
|
Posted: Tue Feb 22, 2011 8:25 pm Post subject: |
|
|
It depends on the condition of your stainless for the cost to restore. Check with Ken Young at http://www.classicstainlessshop.com/. I was happy with his "show quality" polishing. I just received some reproduction flippers for my hardtop and they need polishing to make them look like the rest of the stainless.
Don |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Epperson Bel Air
![](http://i152.photobucket.com/albums/s164/truck490/DSC00627-1.jpg)
Joined: 05 Dec 2006 Posts: 299 Location: Dallas
|
Posted: Tue Feb 22, 2011 8:30 pm Post subject: Polishing Stainless |
|
|
It's not difficult to polish but it is time consuming. Save a dollar and do it yourself. Buffer motor with polishing wheels and polishing compound less than $50.00. A lot less than paying someone to polish if you have the time. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
David Graves Site Admin
![](http://www.dallasclassicchevy.com/images/00%20Misc%20personal/dag%20avatar.jpg)
Joined: 02 Jun 2005 Posts: 1384 Location: Warsaw, TX
|
Posted: Tue Feb 22, 2011 9:51 pm Post subject: |
|
|
WRENCHES has a buffer available to borrow, check out the details under the WRENCHES section and 'Specialty Tools' topic, if you're a club member (don't know who you are because your profile isn't filled out) you can borrow this or any tool listed in the 'Specialty Tools' topic over in WRENCHES.
![](http://www.dallasclassicchevy.com/images/buffer.jpg) _________________ In My Garage -
'55 Bel Air Hardtop
'55 Bel Air 2dr Sedan
'56 Corvette
'67 Camaro RS
'69 Blown 427 nostalgia front engine dragster
'17 Indian Chief Vintage |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Marv Cowden Bel Air
Joined: 18 May 2009 Posts: 208 Location: Grand Prairie
|
Posted: Wed Feb 23, 2011 8:40 am Post subject: Stainless repair |
|
|
Polishing is one thing, removing small dents and scratches is quite another. How about someone who is experienced in all of the above giving a technical session some weekend? |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
2NDTIMEAROUND Bel Air
![](http://www.dallasclassicchevy.com/images/jody.jpg)
Joined: 12 Feb 2007 Posts: 71 Location: Mesquite, Tx.
|
Posted: Sat Feb 26, 2011 12:22 am Post subject: |
|
|
I am no expert by any means, however, I am giving myself a crash course in polishing my stainless trim. Also, please keep in mind that I'm not build a "show car", just a nice "driver". I was told that Trim Polish in Cameron, Tx. did very nice work....at $20.00 a linear foot. So on my BelAir, I figured it would be around $1000.00 - $1500.00. There is actually a lot of good information on YouTube. I purchased my Buffer Motor w/Buffing wheels, a stand, compound, and gloves for holding the parts, at Harbor freight for around $80.00. My recent experience has shown that you need to evaluate what grit of sandpaper to start with. If I have a piece that does not have any bad scratches or dents, I've been starting my sanding with 500 grit. If there are some deep scratches, I start with 320 grit and using a block when I can. After the 320 has seemed to do it's job, I then move on to 400 - 500 - 800 - 1000 - 1500 and finally 2000. By this time, the part has a pretty nice reflection. This is when I go to the buffer. I first use the brown compound on a spiral sewn wheel ( I think that's correct). Then finish with the green compound on a loose cotton wheel. I've been pleased with my results so far. Larry is correct, it's very time consuming. But if your persistent, the personal reward feels great.
Tapping out dents is a bit more tricky. Again, YouTube has some very informative segments on how to tap out the dents. In short, after tapping out the dent, you can start with the 320 grit on a block, sanding down high spots, then proceed with the graduation of sandpaper mentioned earlier. What I did to get my feet wet with this process, was to get one of the worst pieces I thought I would need to replace and use it to experiment with. This way, nothing lost, but, I just might gain a piece of trim I can use. The process is by no means the "way it should be done", it just seems to work for me and gives me a finish that I'm pleased with and it seems to be improving. There is a photo of one of my first pieces with my postings under the "Misc" forum, "Show Us Your Project". Good Luck..and be patient. ![Wink](images/smiles/icon_wink.gif) _________________ "Getting older is inevitable......acting your age is a choice....I choose not to! |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
belairvette Bel Air
Joined: 18 Oct 2005 Posts: 159 Location: Granbury, Texas
|
Posted: Wed Sep 12, 2018 7:01 am Post subject: Stainless Polishing |
|
|
If you decide to have someone polish your stainless, remove the cheap masking tape immediately after receiving it. It will become brittle within days. Hours will be wasted by you or a shop chipping it away then cleaning away adhesive residue. If stainless or chrome came with your car, keep it. I wasted many shop hours fitting an aftermarket grill when I could sent my original to Paul’s Plating and saved beaucoup bucks. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|